Yesterday, I also included a 2x3" Zinc Plate and this seems to change the color of the 99% Cu Plates (6x4"). Yesterday I also used a slow cooker with a ceramic bowl to low heat. So NaOH + H2O solution + 3 Cu (plates) + Zn (1 plate).
The slow cooker method seems to work the best, but I am still learning and next time I will just include Cu Plates.
The wire mesh also seemed to be nano coated some, but this material is made of Galvanized Steel (which is) Zinc (Zn) + Iron (Fe) at high temps to purify the iron to Steel then sprayed with a Zinc coat to protect. (Maybe stainless steel would work best, rather than galvanized Steel) ... less
November 15, 2015
John Czophi charles i can't comment on your face book page. I had trouble setting up my valley forge plasma group Facebook. If i could help just let me know i will do what i can.
I used crystal heat brand caustic from home depot. It seemed to work well on the cop... morehi charles i can't comment on your face book page. I had trouble setting up my valley forge plasma group Facebook. If i could help just let me know i will do what i can.
I used crystal heat brand caustic from home depot. It seemed to work well on the copper nano coating.
March 10, 2016
Keith Kircher: I dont know if anyone has had any burns from their caustic but i found that a can of Sprayaway brand glass cleaner will neutralize caustic almost instantly. It contains no ammonia or vinegar and stops the burning right away.
November 14, 2015
Edie Lee
Thanks for that information; I completely forgot about that as an option.
Keith Kircher: Has anyone thought of how to pull any different gases out of the air? I have been working on a way to get propane, butane, or something that has an obvious energy to it into a GANS state. I was also thinking of making an attempt at GANS with vinegar and u... moreHas anyone thought of how to pull any different gases out of the air? I have been working on a way to get propane, butane, or something that has an obvious energy to it into a GANS state. I was also thinking of making an attempt at GANS with vinegar and using silver plates and see what i get. I know there has to be a million ways to pull gas out of the air. So much to do and not enough time in the day.
November 14, 2015
Keith Kircher: Anyone have thoughts on royal blue caustic? It was originally used on zinc and then i used it on my copper wires, then copper plates. Its pretty to look at but i think it caused my nano coatings to dissolve in saltwater.
marko velikonja
Most probably is also sp3 copper in it. Try to store it in plastic for chemicals or at least put it also in second container as it disintegrates container you are using easily. It can be useful for some applications.
Charles Sharpe: Copper Wire Spool Box - Anyone know of a creative way stripping 14 gauge wire? I tried using the tip of a nail, but this did not work. My drill broke the copper in two frown emoticon
If i can cut the coating while the 7 amp electric drill pul... moreCopper Wire Spool Box - Anyone know of a creative way stripping 14 gauge wire? I tried using the tip of a nail, but this did not work. My drill broke the copper in two frown emoticon
If i can cut the coating while the 7 amp electric drill pulls the wire, i would save money and time winding my coils.
Kent Estes
You don't have to use the potatoe peeler in that automated video, affix a blade at proper angle.
January 12, 2017
Kent EstesI found that using a sharp stiff pocket knife works better than razor. Step on wire with shoe, pull the wire tight and strip downward.
Faster way is to find the correct surface to hold your knife against the wire and pull with other hand.
I was able to st... moreI found that using a sharp stiff pocket knife works better than razor. Step on wire with shoe, pull the wire tight and strip downward.
Faster way is to find the correct surface to hold your knife against the wire and pull with other hand.
I was able to strip 50 feet in just a few minutes that way, but then you have to cleanup and wind the copper wire.
January 12, 2017
Kent Estes
Lowe's and home depot will give you the empty wire spools by the way.
January 12, 2017
Kent Estes
But I'm with John Crop here, I'm ordering a roll of 14 # next round.
Keith Kircher: My nano plated copper plates are losing there coating in a salt water solution. I steamed them a dozen times and dried them for 3 three days. I think my copper was coated in something because my caustic solution is a royal blue color. Any thoughts? By the... moreMy nano plated copper plates are losing there coating in a salt water solution. I steamed them a dozen times and dried them for 3 three days. I think my copper was coated in something because my caustic solution is a royal blue color. Any thoughts? By the way my name is Keith and im from AZ. I figured Idaho was as local as i was going to get.
November 14, 2015
Charles SharpeI have not seen this problem before Keith, hopefully the community could help. I just finished my coil winding setup and begun nano coating 3 copper plates just about an hour ago.
Where did you purchase you copper plates? I found some at a metal cutting... moreI have not seen this problem before Keith, hopefully the community could help. I just finished my coil winding setup and begun nano coating 3 copper plates just about an hour ago.
Where did you purchase you copper plates? I found some at a metal cutting workshop yesterday for 1 x 1 ft (~19.00 )
What salt did you use? Also, did you use distilled water or tap water? The solution to water / salt should be .09 ratio from what Mr. Keshe said. (multiples of 3, 6, & 9 are always a good place to start)
It is hard to help without more details since this is new to me. less
November 14, 2015
Keith KircherI used distilled water. That is all i drink now(different subject).I googled the salt to water ratio in the ocean because i heard him say that sea water was best. I ordered sea salt for my solution and essentially reproduced ocean water. The ocean is a 32... moreI used distilled water. That is all i drink now(different subject).I googled the salt to water ratio in the ocean because i heard him say that sea water was best. I ordered sea salt for my solution and essentially reproduced ocean water. The ocean is a 32 to 1 ratio. Thanks for the feedback.
John Czop
Valley Forge Plasma Group, Did you drain off the mill volts prior to letting them dry with some caustic in the container. this help build up the nano coating.
Keith Kircher
I am very happy and grateful to be a part of the Keshe Foundation. I look forward to re-discovering my learning potential. May we all make a positive change for the world we live in.